Vmware Vcenter Protect Error 501
In addition, patch groups are now created and managed from within Patch View. This gives you better visibility into the current state of your deployments.Deployment Return CodesDeployment return codes are now available within Deployment Tracker and within the deployment reports. Scan not performed.A machine exists at this IP address but it is either not listening on, or is blocking access to, TCP ports 139 and 445.Error Code 270:Connected to a machine This may occur if scanning a currently unsupported virtual image platform. his comment is here
Review the document: http://community.shavlik.com/docs/DOC-23052 Error Code 622:Machine OS is not Recognized. The mounting process timed out after 60 seconds. Error reading Registry.A general registry error has occurred. The scan engine was unable to read the vmx file and/or this file had no hard drives configured for the image. https://kb.vmware.com/kb/1004887
See the following KB: http://community.shavlik.com/docs/DOC-2233Error Code 200:System not found. Protect 9.1 will support this version of Windows until it reaches its end-of-life, which has not yet been announced. Refer to the following document:http://community.shavlik.com/docs/DOC-22997 An Export of the following registry keys from the target system: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion HKEY_LOCAL_MACHINE\SOFTWARE\Classes\Installer\Products Applies To Shavlik Protect 9.x 0 0 The following VMware virtual infrastructure configuration is required for installing Kaspersky Security for Virtualization 1.1: VMware ESXi 5.1 hypervisor (build 709733), ESXi 5.0 hypervisor (patch 1, build 474610 or higher) or VMware ESXi
See the following KB: http://community.shavlik.com/docs/DOC-2233 Error Code 200:System not found. This may be a feature request. Error Code 702:File https://www.microsoft.com/technet/secur ... Please make sure that the VMware Virtual Disk Development Kit has been properly installed.
Please run with tracing on and send to technical support. The current or specified user account performing the scan does not have administrative rights to the machine being scanned. Scan not performed. http://blogs.vmware.com/kbdigest/2012/10/new-articles-published-for-week-ending-92912.html To turn this feature off, remove the registry value [HKLM\Software\Microsoft\Fusion!EnableLog]. Cause This is caused by a missing patch: Q2468871, MSWU-544, Non-security Patches Solution Install the pre-requisite
If this file is inaccessible, the prerequisite validation fails and the scan is aborted. Error reading Registry
A new dialog, available via the Manage > Scheduled Console Tasks menu, enables you to view and manage these tasks.ReportsA new End-of-Life by Product report is now available. https://community.shavlik.com/docs/DOC-2159 Contact your technical support group. Error Code 806:Error mounting hard drive at '%s' to drive '%c' An attempt to mount the virtual image was not successful. It lists many missing patches, one of them is MSWU-765 (Q2836939).
The scan engine was unable to mount the virtual image because the virtual image was powered on. this content Please run with tracing on and send to technical support. Resolved an issue where Predictive Patch Download would error out if any of the defined downloads do not have a URL.Resolved an UI discrepancy that made a deployment appear it would Error Code 823:Could find default boot section in the BCD for image at '%s' The scan engine was unable to enumerate boot information from the boot configuration data (BCD) for this
Scan not performed. Error Code 817:Error parsing system file at '%s' The scan engine was unable to read the vmx file for the specified VMware Workstation or VMware Server image. If the XML file is not obtained from the network, an attempt is made to locate an existing version of this file on the local machine.Error Code 799:Itanium class servers are weblink Error Code 701:File http://download.microsoft.com/download/ ...
HOME | SEARCH | REGISTER RSS | MY ACCOUNT | EMBED RSS | SUPER RSS | Contact Us | Shavlik User Community : All Content - Shavlik Protect http://community.shavlik.com/community/feeds/allcontent?community=2009 Are you Contact support for assistance.Error Code 808:Could not get return code from mounting tool when mounting hard drive at '%s' to drive '%c' due to %sThe virtual image mounting process completed but Password.
Customers should work towards moving to newer editions of SQL Server as soon as possible.User Criticality Filter will be removed after Protect 9.1With the introduction of the Vendor Severity filter, the
We will review your feedback shortly. secure.cab was NOT downloaded.The signed, compressed CAB file containing the security patch information could not be obtained from the specified location. This error message applies to Vista images only. The driver comes with VMware Tools included in VMware ESXi 5.0 patch 1 hypervisor.
Check to see that your scanning machine is properly connected to the network and that the machine being scanned is still connected to the network. This reduces memory usage and provides better performance.Scheduled operations that were previously configured in Tools > Options have been moved to a new area under Tools > OperationsManagement of distribution servers Show 13 replies 1. check over here This could be caused by running a non supported configuration.
Each and every idea is reviewed and given serious thought on if and how your idea could be implemented. secure.xml was NOT downloaded. Resolved an issue where attempts to delete a partial scan result could result in a console crash. This may occur if the administrator has unshared the systemroot (typically C$ or similar) or has disabled the AutoShareServer(Wks) via the registry.See: Scan Error 301 - SystemRoot Share Access Required to
The URL protectservices.shavlik.com must be accessible when communicating with Protect Cloud. Affected Products Shavlik Protect 9.x 0 0 07/30/13--00:30: How to Submit a Feature Request Contact us about this Check to see that your computer (the scanning machine) is properly connected to the network and that you can remotely logon to the specified machine.Error Code 202:System not found. This error message applies to Vista images only. Scan not performed.
This article lists the most common scan error messages and provides some guidance on correcting the issue. Cause Scan errors can occur: If one or more of