Home > Vista Error > Windows Vista Error Message User Profile Cannot Loaded

Windows Vista Error Message User Profile Cannot Loaded

Contents

Boot into safe mode, as above. I am a new to "How-to-Geek" and just want to thank you for this topic, I am finding it very useful. Lucia St. Please try again later. Check This Out

In the command prompt type: Net user administrator /active:yes Hit Enter and you should see a message that says, "The command completed successfully". WINDOWS 10 FIX If you've encountered the 'User Profile Service failed the logon' error in Windows 10, there's a slightly different fix but it requires you to have access to another Troubleshooting Common Blue Screen Error Messages Stop 0x000000ED (UNMOUNTABLE_BOOT_VOLUME) Stop 0x0000007B (INACCESSIBLE_BOOT_DEVICE) These two errors have similar causes and the same troubleshooting steps apply to both of them. You need to run the full system diagnostic.

Windows Vista Error Message User Profile Cannot Loaded

Instead click on Start, type Regedit and hit Enter. When you run Startup Repair, it scans your computer for the problem and then tries to fix it so your computer can start correctly. You must download and install the application (15 MB) from the Microsoft web site. When troubleshooting this error, your task is to find out why the Windows kernel is confused and fix the cause of the confusion.

STOP 0x000000D1 (DRIVER_IRQL_NOT_LESS_THAN_OR_EQUAL_TO) This stop code indicates a driver tried to access a certain area of memory when it should not have, meaning there is a flaw in the driver itself. If both the video driver and the system BIOS are fully up-to-date, check with the manufacturer for recent driver updates. To restore your computer's operating system and software to the original factory settings, launch the link below: Launch the Microsoft Windows Reinstallation Guide

Article ID: SLN128762 Last Date Modified: 07/29/2016 Tap the F8 key on the keyboard immediately after the Dell logo screen disappears until you see the Windows Advanced Options Menu on the screen. (If the Windows Advanced Options Menu

Click the link below to being the troubleshooting process: How to troubleshoot a problem by performing a clean boot in Windows Vista or in Windows 7 Step 10: Restore the Operating Microsoft Support Windows can occasionally run into problems reading your user profile if you happen to have an antivirus scan running at the time. Troubleshooting Common Blue Screen Error Messages 0x000000ED and 0x0000007B 0x00000024 0x0000007E and 0x0000008E 0x00000050 0x000000D1 0x000000EA Using the Windows Debugger This article describes what Blue Screen errors are, why they occur, https://support.microsoft.com/en-us/kb/931276 After a reboot, you'll have the Registry back in its initial state before you made any changes.

Uninstall any recently installed programs, and roll-back any recently installed drivers. These stop codes always occur during the startup process. The system returned: (22) Invalid argument The remote host or network may be down. Reports: · Posted 5 years ago Top vistamike Posts: 10945 This post has been reported.

Microsoft Support

Your computer will take a backup of key files and the Registry. More Bonuses Error code 0x8007000D Unable to open the license. Windows Vista Error Message User Profile Cannot Loaded Event ID codes updated : http://www.chicagotech.net/wineventid.htm Edit: Security Event ID logs : http://www.ultimatewindowssecu.....ventid=675 Reports: · Posted 5 years ago Top GuiltySpark Posts: 4024 This post has been reported. Windows 7 Why not introduce yourself here, members will surely greet you.

Reinstalling Windows is not likely to prevent this error from reoccurring. his comment is here You can also try to restore Windows to an earlier state using System Restore and then try to activate Windows again. Reports: · Posted 5 years ago Top marks100 Posts: 4507 This post has been reported. Please try the request again. Windows 10

Thank you. The link in the first post is no longer in service the new link is : http://www.hosting.com/search?query=error+codes Reports: · Posted 5 years ago Top GuiltySpark Posts: 4024 This post Step 9: Use Clean-Boot Troubleshooting to Isolate the Software Issue A program or application may be interfering with the normal boot process of Windows. http://digitalfishbowl.net/vista-error/windows-vista-blocked-startup-programs.html NN is the sequence the dump files were created in if multiple dumps were generated on the same day (the first crash dump on a given day will be numbered 01,

System error codes : http://msdn.microsoft.com/en-us/library/ms681381(VS.85).aspx Reports: · Posted 5 years ago Top zs474 Posts: 887 This post has been reported. Press Down Arrow until Repair Your Computer is highlighted, and then press Enter. When you're at the desktop get up a Command Prompt and type in rstrui to load System Restore.

Kitts & Nevis St.

As you can't get into your computer, it may be prudent to take its hard disk out and save the files to another computer or laptop. Before you can use the tool, keep in mind the following: The Windows Debugger is not a native Windows tool. ABOUT About Us Contact Us Discussion Forum Advertising Privacy Policy GET ARTICLES BY EMAIL Enter your email address to get our daily newsletter. Windows 10 Windows 8 Windows 7 Windows XP Dell Recommended: How to fix BlueScreen (STOP) errors that cause Windows Vista to shut down or restart unexpectedly What Is a Blue Screen

If this fails to correct the problem, try the next most recent restore point until you find a restore point that resolves the issue. Using the Windows Debugger The Windows Debugger is one of the primary tools used by Microsoft software developers and support staff to analyze and resolve errors that result in memory dumps, To do this, restart your computer and hit F8 to bring up the Windows 7 or Vista boot menu. http://digitalfishbowl.net/vista-error/vista-error-0x0.html Deselect 'Hide protected operating system files (Recommended)'.

STEP 2 - CHANGE REFCOUNT Select the folder with the .bak in the name, then in the main Window double-click RefCount. RESTART YOUR COMPUTER This might sound obvious, but try restarting the system as a first port of call. If none of the above solves the issue, reinstall Windows. We'll show you how in this article.

To fix this issue, restore original Windows Vista edition in your computer and the try to upgrade. Log in as a user with administrative rights, and click OK. If those diagnostics pass, run a full file system check from the Recovery Console (chkdsk /f /r) to detect and (potentially) fix any corrupted data. If your computer does not boot to Safe Mode, select from the following options to troubleshoot.

This test takes approximately 5 minutes. Please try the request again. Restart your computer and tap F8 after the BIOS POST test messages to bring up the boot menu. Solution: This error code occurs when you use "Windows Anytime Upgrade" (WAU) feature and indicates that the initial download may have been corrupted.

Things to check The SATA controller configuration in the system BIOS If the SATA controller gets toggled from ATA to AHCI mode (or vice versa), then Windows will not be able When you're at the Desktop, log off and log into the Administrator account you used in Step 2. Generated Tue, 01 Nov 2016 03:26:59 GMT by s_wx1199 (squid/3.5.20) To use the tool, follow these steps: Download and install the Windows Debugger from the Microsoft Web Site .