Home > File Status > Vsam Return Codes

Vsam Return Codes

Contents

For example, a permanent I/0 error may have occurred when VSAM was reading or writing a catalog entry or catalog recovery area record. X'54' 084 Return Code=08 Action=Request Locate mode was specified for a PUT request of for processing in a user buffer. Or Disk full for a sequential file or sort file. 35 OPEN SORT "FILE NOT FOUND", An OPEN operation with the I-O, INPUT, or EXTEND phrases has been PROGRAMMER ACTION: The VSAM OPEN return code will be handled internally by the VSE/VSAM Space Management for SAM Feature by requesting operator authorization to delete the unexpired file. check over here

A sequential READ operation has been tried on a file open in the INPUT or I-O mode but no valid next record has been established because: The preceding READ statement was PROGRAMMER ACTION: Ensure that in the SYNAD exit routine your program issues a DUMP macro. The value is placed in the status key before execution of any EXCEPTION/ERROR declarative or INVALID KEY/AT END phrase associated with the request. Rerun your job. http://www.simotime.com/vsmfsk01.htm

Vsam Return Codes

VSAM Logical error codes These codes indicate VSAM errors. X'BC' 188 Return Code=>0 Action=CLOSE The ACB to be close is currently being used; (for example, by a SHOWCB or TESTCB macro). PROGRAMMER ACTION: Restructure your program so that fewer files are open concurrently. This is probably a system error.

Not enough programmer logical units were available. For Local Shared Resources, the ACB addr is not same as for a previous request that used the same RPL. Examples of these incompatibilities are: The DTF BLKSIZE is too large to fit in the maximum RECORDSIZE defined for the file. Vsam File Status 93 Possible violations are: The EXTEND or OUTPUT phrase was specified but the file would not support write operations.

Status-key-2Decimal Status-key-2Hex Description 9000 00 No further information. 9001 01 Insufficient buffer space. Vsam File Status 39 Eliminate duplicate records by processing the data using keyed access with update. PROGRAMMER ACTION: Rerun the job when there is less concurrent activity in the system. Possible causes: Attempting to WRITE or REWRITE a record that is larger than the largest, or smaller than the smallest record allowed by the RECORD IS VARYING clause of the associated

Programmer Respone: Do one of the following: Correct the problem that caused the preceding catalog recovery operation to fail. Vsam File Status 97 PROGRAMMER ACTION: If problems occur due to inconsistent extent information, display the VTOC and execute the Access Method Services LISTCAT command and compare the extent information. This message is accompanied by message 4233A. An attempt was made to access a file for input with conflicting or invalid disposition specified on the job control statements.

Vsam File Status 39

All Rights Reserved.   Sitemap Share Here.. End of File encountered ttempted to READ a relative record outside file boundary nvalid Key - Sequence error nvalid Key - Duplicate Key found nvalid key - No record found nvalid Vsam Return Codes PROGRAMMER ACTION: Change your application program to avoid attempts to close an ACB that was never opened, has already been closed, or was erroneously modified to to appear closed. File Status 37 In Vsam PROGRAMMER ACTION: Verify that your program is using the correct cluster, alternate index, or path name.

The information about volumes is retrieved from the catalog, and programmer logical units are automatically assigned by VSAM. http://digitalfishbowl.net/file-status/vsam-file-status-23.html If Catalog Check finds no errors, the problem was due to insufficient storge. Return Code=0C Action=Request VSAM failed to read index-set records of an index. The file has been opened successfully. Vsam File Status 92

Return Code=08 Action=Request Not enough buffers are available to process the request (shared resources only). Invalid or incomplete file information Possibilities: Open an ESDS as a KSDS or vice versa, Attempt to open a non-loaded file as INPUT or I-O, Attempt to open a loaded file Current Server or Internet Access The following links may be to the current server or to the Internet. http://digitalfishbowl.net/file-status/vsam-error-codes.html Refer to the section for Status-Key-1 being equal to "3" for additional information based on Status-Key-2. 4Logic Error, a program is attempting a file access function in an improper sequence or

PROGRAMMER ACTION: Rerun the job when there is less concurrent activity in the system. File Status In Cobol Example X'2C' 044 Return Code=08 Action=Request The work area you have supplied (in the AREA = addr operand for the RPL) is not large enough for the requested data record. Return Code=08 Action=Request No record found.

The error may be caused by such conditions as VSAM finding an unformatted record when expecting a formatted record, a volume containing data other than that expected, or an I/O error.

Possible causes:For a READ statement the key value for the current key is equal to the value of that same key in the next record in the current key of reference.For DISP=NEW was specified for an input file. OPEN did not try to verify its catalog records. Vsam File Status 90 We have a team of individuals that understand the broad range of technologies being used in today's environments.

X'72' 114 Return Code=00 Action=OPEN The Catalog Check Service Aid was invoked during OPEN processing and detected a catalog irregularity, or there was insufficient storage for Catalog Check processing. For relative and indexed files in the sequential access mode: The last I/O statement executed for the file, before the execution of a DELETE or REWRITE statement, was not a READ X'01' 001 Return Code=04 Action=CBMM GENCB/MODCB/SHOWCB/TESTCB request is invalid.

X'02' 002 Return Code=>0 Action=CLOSE CLOSE or TCLOSE found an invalid control block structure for this ACB. have a peek at these guys PROGRAMMER ACTION: Rerun your job.

Issued a sequential PUT insert request for a relative-record file without having VSAM positioned for this request. Return Code=08 Action=OPEN A permanent I/0 error was detected on the system lock file. PROGRAMMER ACTION: Make sure the file-id in your DLBL statement does not specify the name of a default model. This information message indicates that the catalog records for this file are correct, but its catalog statistics may be incorrect.

X'6E' 110 Return Code=08 Action=OPEN You attempted to open for input only (ACB MACRF=IN) a file which was empty (no record in it) or a file was not properly closed on Rerun the job after the system problem is corrected. X'4F' 079 Return Code=08 Action=OPEN A catalog management error was detected during implicit define. It was exported with the TEMPORARY and INHIBITSOURCE options and updating is not permited.

X'48' 072 Return Code=08 Action=OPEN The file-id specified in your DLBL statement was not found in the catalog, and insufficient allocation information was specified for an implicit define. Either: A programmer logical unit is not available in this partition (available programmer logical units have been used by ASSGN job control statements, or VSAM automatic assignments for files, catalogs or A READ statement was successfully executed, but the length of the record being processed did not conform to the fixed file attributes for that file. System Action: Close processing continues to successful completion, assuming no other complications.

In this case, the physical size of the new record is allowed to be smaller than that of the record being replaced. 46 A sequential READ operation has been tried on After correcting errors, rerun the original job. X'46' 070 Return Code=08 Action=OPEN An invalid file-id was detected during implicit define or implicit delete. Return Code=08 Action=OPEN Same explanation as for CLOSE. If you experience a problem with this page, please send a message to [email protected] including a description of the problem.