Home > Error Code > Vita Spa Error Codes

Vita Spa Error Codes

Contents

About eHow Advertise Write For eHow Contact Us Connect with us Terms of Use Report Copyright Ad Choices en-US Privacy Policy Mobile Privacy demandmedia.com © 1999-2016 Demand Media, Inc. The following is a list of most probable causes of this message. Check for proper spa water level and ensure pump is primed. Pressure switch is not working.SN = Non functional high temperature sensor. http://digitalfishbowl.net/error-code/vita-spa-pb-error-code.html

One sensor has detected 118º F at heater. Check for proper spa water level and ensure pump is primed. Spa has shut down. All rights reserved. click

Vita Spa Error Codes

Best, Gina~Moderator Ask Your Own Pool and Spa Question Customer: replied3 years ago. DO NOT ENTER THE WATER. Note: The control system brand name is usually different from the hot tub brand name.

hot = Overheating, water over 112° F. The fundamental reason is water flow through the spa control system, if the water is not flowing at a rate to satisfy the switch, it will result in one of the Heater is deactivated. Balboa Spa Control Manual Then re-start the hot tub, if the error code goes away, the problem was either a dirty filter (clean or replace) or too many jets were closed off.

Touch any button to reset the system. Hot Tub Error Codes If display shows only this message (blinking) spa is shut down. FL1 = Water flow problem, inhibited or pressure switch malfunction. this contact form Protect from FreezingCover Cleaning and AdviceAcrylic Surface Care and MaintenancePurchase a "Made for Michigan" Spa Cover>Spa Cover MeasuringPurchase a Spa Cover Lift AssistantWhirlpool & Air Bath TubsSystem Cleaning-Home remedyAcrylic Surface Care

Goes right back to Hl then HILI flashes .SO... Gecko Spa Pack Error Codes characters left:

Contact Us|Terms of Service|Privacy & Security|About Us|Our Network|Sitemap © 2003-2016 JustAnswer LLC JustAnswer UKJustAnswer GermanyJustAnswer SpanishJustAnswer Japan 426 12751686 Login|Contact Us Pool and Spa Questions about Pool Repair? Major Fault* * * (3 flashing dots under temp display)Flow/Pressure switch either Open or Closed Circuit* * * (as above, plus illuminated red LED on PCB)High Limit Fault Flashing Light Error Check that circulation pump is plugged in, or for possible loose connection.

Hot Tub Error Codes

Heater is deactivated. The spa is at a temperature above 108° . Vita Spa Error Codes Low speed pump and heater will activate until spa reaches 65ºF.OH = High temperature condition, has reached 110ºF. Balboa Hot Tub Error Codes How to Turn on a Vita Spa.

If that doesn't fix the issue, professional service is needed because the control board may be damaged. weblink One sensor has detected 118º F. Chris Questioner's RatingRating(1-10)Knowledgeability = 10Clarity of Response = 10Politeness = 10CommentNo Comment Add to this AnswerAsk a Question Related ArticlesJeep Wrangler Heater Core LeakingMaintaining a Hot Water HeaterTroubleshooting a Water Heater ALWAYS SHUT THE POWER OFF AT THE DISCONNECT BEFORE ATTEMPTING THESE PROCEDURES. Vita Spa High Limit Sensor

PnL = Communication between the panel and circuit board is faulty. ---- = "Watchdog" (spa is deactivated) A problem has been detected. Heater is deactivated. HomeTestimonialsBlogIndustry LinksPolicies, Warranties and DisclaimersService Area-Contact UsSpas / Hot Tubs & Swim SpasFilter Cartidge Cleaning - Home remedySterilizing before UsageProperly Closing-WinterizingError Codes-Digital or Blinking Indicator LightWinter Trouble? http://digitalfishbowl.net/error-code/vpn-error-codes.html This indicates a persistent flow problem The heater is shut down while all other spa functions continue to run normally.

HLoH = Hi Limit Over Heat. Sundance Spa Error Codes Hold = Panel sensors have been pressed too many times in a short period of time.HOT = Circuit Board temperature has exceeded acceptable limit.ICE = Freeze protection. Category:Pool and Spa Share this conversation Expert: Fix my Pool and Spa replied5 years ago.

Do not use spa when temperature is flashing or the OH message is displayed.HLoH = Hi Limit Over Heat.

This is a normal spa function; no further action is necessary.When either sensor reads below 40 degrees F., the system provides freeze protection. If message comes back, call for service. Hope this helps you out. Gecko Spa Pack Troubleshooting Hot Tub Repair Codes The codes are often initials that represent a shortened error message. ...

Flo = Improper flow or pressure switch malfunction Cool = Water temp 20° below set point ICE = Potential freeze condition has been detected Sn1 = Hi-limit sensor malfunction Sn3 = It automatically activates all of the pumps and the blower to circulate water and warm the plumbing. No action is necessary.PnL = Communication between the panel and circuit board is faulty.---- = "Watchdog" (spa is deactivated) A problem has been detected.Sn1 = Open sensor (heater is deactivated) or his comment is here Balboa (used by Belize Spas and many other hot tubs) pd = Power supply, unit running on battery backup OH = Sensors reading 112-118° F.

COOL = Spa water is more than 20° F cooler than the temperature set point.FLO* = Flow Switch (heater is deactivated. Insufficient water flow through Heater. HL = High limit switch tripped. If alternating with temp, may be temporary condition.

Hide thumbs 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 Brett Aqualine OH = Temp exceeds 118° F Fr = Freeze condition - temp below 40° F FL = Pressure switch failure EO = Shorted temp sensor E1 = Open temp Note: A common programming mistake is overlapping filter times that may cause the spa to filter continuously.• Check the water level.• Check the water temperature with an accurate temperature thermometer. Water temperature has reached 118ºF.

HL = High limit switch tripped.