Home > Error Code > Hot Tub Error Codes

Hot Tub Error Codes

Contents

Contact ACC. Heater disabled but spa operational SH Short circuit on temperature sensor Sn1 Hi-Limit fault, water may be dangerously hot Sn2 Temperature sensor fault, Heater deactivated Sn3 Temperature sensor fault, Heater deactivated Rare system error. One sensor has detected 118º OHS Overheat. this contact form

Do not enter the spa. if the heater is not working does that also affect the blower which causes the bubbles?Customer : The water temperture is probably around 20 degrees its never been turned off it Sn1 = Open sensor (heater is deactivated) or Shorted sensor (spa is deactivated). Heater disabled but the spa is operational.

Hot Tub Error Codes

when i first got it you could sort of feel it heating,Poolservice123 : When in ICE mode it will only heat when it runs and the blower runs as well which If alternating with temp, may be temporary condition. Spa is shut down.Pr = When spa is first actuated, it will go into Priming Mode.ILOC = Interlock failure - possible pump or ozone spike .(---) =Unknown water temperature. (Displays when Wondering what your spa is trying to tell you?

drops. Heater disabled but spa operational. LO Freeze Condition detected; Warm up procedure begins. Gecko Spa Pack Error Codes The Spa or Hot Tub Panel Displays: SN, Sn1, Sn2 Sn3, HL, E1, E3, Prh, HtS, Blinking Lights Again these can be caused by a flow issue.

The other pumps and the blower will purge for 30 seconds to 2 minutes at the end of the freeze condition. Customer : current temp is 60 fCustomer : how do I get the ice out of everything?poolguy810 : The easiest way, if there is enough room, take your access door off, by draining the water and refilling. dr = Inadequate water detected in heater.

Heater disabled but the spa is operational. Balboa Spa Control Manual Entire system is disabled. Get a Professional Answer Via email, text message, or notification as you wait on our site.Ask follow up questions if you need to. 100% Satisfaction Guarantee Rate the answer you receive. If you spa has been configured for low amperage it may not come out of ICE mode until the freezing situation passes.

Balboa Hot Tub Error Codes

Spa unusable. check this link right here now Check for proper spa water level and ensure pump is primed. Hot Tub Error Codes Major Fault - - Temperature unknown - displayed at power up for 2 minutes - not a fault - 01 Hi-Limit fault - 02 Temp sensor fault - 03 Flow/pressure switch Vita Spa Error Codes In rare cases (usually warmer climates), the circulation pump may also cause overheating.

ToE = Time out error. http://digitalfishbowl.net/error-code/msi-exit-codes.html Alphabetical Error Code List * * * (3 flashing dots under temp display) Flow/Pressure switch either Open or Closed Circuit * * * (as above, plus illuminated red LED on PCB) Spa unusable. Check for low water level and ensure pump is primed. Marquis Spa Error Codes

You can often determine the make of the control system by looking inside the spa's equipment area. Hi limit sensor is disconnected, shorted, or spa temp is above 112° F. * SEoP : Sensor open or disconnected. Sundance Spas Error Codes COL: Temp 20F below set point ILOC: Interlock failure - possible pump/ozone spike FLO/FL1/FL2: Flow/Pressure switch malfunction Hold: Panel buttons pressed to many times/quickly HOT: PCB temperature navigate here I CE2 = Freeze protection.

ICE2 = Freeze protection. Coleman Spa Error Codes Heater is deactivated * F2 : 4 hours daily filtration * F4 : 8 hours daily filtration * F6 : 12 hours daily filtration * FC : continuous filtration EasyPak Error Credentials confirmed by a Fortune 500 verification firm.

PSoL = Pressure switch open with low pump.

Heater is deactivated. Low speed pump and heater will activate until spa reaches 65ºF OH: High temperature condition, has reached 110ºF. So you are saying that it never heated? Spa Command Panel Instructions Place of registration: Winghams House, 9 Freeport Office Village, Century Drive, Braintree, Essex CM77 8YG.

Water temp has reached 118ºF. HLoH = Hi Limit Over Heat. One sensor has detected 118º * OHS : Overheat. http://digitalfishbowl.net/error-code/vpn-error-codes.html Suite 2, 23 Robjohns Road, Widford Industrial Estate, Chelmsford, Essex CM1 3AG applies to HotSpring products and not Hot Tub Assist.

OH = Overheating, water over 112° F. One sensor has detected 118º F at heater. Disclaimer: Although we hope this information will be useful, error codes are subject to change without notice. The Spa or Hot Tub Panel Displays: Cd, CLd This indicates that a sensor detects a possible freeze condition.

Brett Spa Side Error Codes OH : Temp exceeds 118 degrees Fr : Freeze condition - temp below 40 degrees FL : Pressure switch failure EO : Shorted temp sensor E1 Sundance Spas ILOC = Interlock failure - possible pump or ozone spike FLO = Pressure switch malfunction or Flow switch malfunction (system specific) Hold = Panel buttons pressed to many times Heater is deactivated. SN = Non functional high temperature sensor.

HFL = Substantial difference between temperature sensors detected. If itwill not reset, check for clogged filters. Heater is deactivated. Sensor plugged into jack B is not working * SnS : Sensors out of balance.

Ask an Expert Online. poolguy810 : Hello, how can I help you today?